Offering a wide range of pet blow moulding machine.

CM-A4 Full automatic blow molding machine is suitable for producing PET plastic containers and bottles in all shapes. It is widely used to produce the carbonated bottle, mineral water, pesticide bottle oil bottle cosmetics.

ZHF2500D/Double Worktables Vacuum Press Machine: It is used for coating different shape base material with PVC film,wood veneer,etc by vacuum abnormality wrapping technology. It is used for coating natural wood carved board,decorative material, MDF, etc. and also can be used for heating print. Especially for high production and efficiency are demanded .

Offering rubber molding machine with following features: 1. This series machines are made of high quality steel and C45 steeling casting plate. Never be cracked and out of shape. 2. This machine is adopted the world famous brand hydraulic units and controlled by PLC system. The PLC system may control different part independently and avoid interference. 3. This machine runs rapidly and smoothly and without noise. 4. Bumping times and bumping time can be set. And the manual operation test can be applied at your convenience. 5. Pressure relief, air drainage and going-down can be adjusted separately with being controlling by time or the auto continuous actions can be preset. 6. Oil hydraulic concentrated circuit: few pipes, few branches. It is with a cooler to keep the oil temperature and oil pressure in balance. The oil would not be leaked. For which, the machine is with a longer serving life. 7. The emergency down switch provides the sudden stop and going-down by slight touch so as to

Offering bottle blow molding machine: The machine is suitable for producing plastic container of toys, foods, cosmetics, cleaning products and chemical products etc. It can blow PE, PVC, PC, PS and other raw materials.* Technical parameters: - Productivity: 2000/hour. - Motor power: 7. 5kw. - Heating power: 13kw. - Air consumption: 0. 7cubic meters/minute. - Air pressure: 0. 65-0. 75mpa.

Casting machines

Offering a wide range of pet blow moulding machine.

CM-8Y heat resistant automatic bottle blow molding machine is suitable for producing any shapes of PET containers and volume is from 10-2000ml. It is widely used to produce mineral water bottles, carbonated beverage bottles, cosmetic bottles, oil bottles and so on.Adopting double crank connecting bar clamping and clamping mould is stable and fast. Adopt for infra-red rotary oven and heated equally.The air system has been divided into two parts: pneumatic action part and bottle blow part to meet the different requirements for the pressure of action and blow. It can provide sufficient and steady high pressure for blowing large irregular shaped bottles.The machine is also equipped with muffler and different parts of refueling system.The machine can be operated in the step-by-step mode and the auto mode.The machine is small with low investment. Its easy and safe to be operated by one person.

YM-3P-B blow moulding machine YM-3P-B two step semi automatic compauter controlled revotary infrared oven heating bottle blowing machine is suitable for producing pp/pet plastic containers in 7l with wide mouth 28-120. It has high air pressure, big clamping force, small size, low power consumption easy to operate and maintain.

The AX-ZL3 Medium Frequency Induction Casting Machine is used for casting alloys in prosthetic dentistry and oral orthopedics. It can be used for refractory alloy melting and investment casting in all fields of dentistry. This machine can be used to deal with special structured removable denture, metal bases of casting crowns, metal-porcelain crowns, and all kinds of clamps. The medium frequency casting machine is the updated version of the high frequency casting machine, so it has all the features of a high frequency casting machine. Furthermore, it has the following advantages: 1. The medium frequency casting machine has an advanced all-transistor circuitry, which makes it a highly efficient, low power consumption and low power rating (2.5kW) machine. 2. No preheating is needed, melting and casting can start immediately after the machine is turned on, the interval between melting and casting is two minutes. 3. The machine can work under the voltage of

Block molding production apply to: 1. Constuction parts for decoration 2. Heat-insulation wall and ceiling 3. 3D panel and sanwich panel 4. Other applications

We have number of used toyo plastic injection mold machines. All are in good working condition and are available for inspection. available toyo machines: toyo TI50G2 (1994) 5-unit toyo TI80G2 (1994) 3-unit toyo SI100 (2000) 1-unit total of 9-units available. The machines will be sold in one lot. We also have number of other used machines.

Mold Change System is for Injection Molding Machine and Die Casting machine. It adopts four independent circuit of cross clamping to clamp the mold. Each hydraulic circuit is with the function of maintaining pressure for a long time. In order to save time for the mold change and ensure the operation safety, it is just in time to apply Qucik Mold Change System.

Features:Pneumatic switch. Seperate heating box, saving electric Rack Balancing systemMovement making system Thermocycling fan Digital temperature control system Hydraulic system Vaccum meter Auto-alarm system Movable clamp, no rejection working table are made of steel.2. Application: Acrylic

We are the professional manufacturer in vertical plastic injection molding machine ,bakelite machine ,sole machine .vulcanizer machine ,have got certification ISO9001:2000.

We are specialized in Liquid Silicone Rubber (LSR) injection molding machine and LSR mould making and Liquid Silicone Rubber (LSR) product manufacturing. Our main products include Liquid Silicone Rubber (LSR) injection molding machine and LSR products company based in China mainland, such as LSR silicone baby teether, LSR silicone baby nipples, LSR silicone oxygen mask, LSR silicone keypad, LSR silicone insole, LSR silicone catheter, LSR cable insulator and so on.

product description: our machine approved by iso9001, 2000. suitable materials: bopp, pp, cpp, pof, pe, etc, which can be used to heat seal and cut(the smoothness of packing materials must be well). functions: automatic coating, folding organ bottom, coating pearly-luster membrane, ultrasonic hobbing, atomatic meter counting, winding and unwinding for materials, magnetism powder brake. This machine is a front production line of cutting machine.

Molding/Thermo-Molding

Horizontal injection molding machines ranging from 28 to 1000 tons are currently located at our facility used to manufacture a wide variety of custom plastic products.

We offer continuous extrusion blow moulding machines, with both single and double stations and long stroke - multi-cavity machines for up to 250 litre capacity.  Our advanced features include:  Single and multi die head capability. Contact control panel color screen operation;  Integrated multiple point parison control system with Moog cylinders from Japan;  Easy-change, tiebar-less clamping system

There are several types of forms, (blocks, plank & panels) the basic function is to provide an interior and exterior polystyrene wall, that when erected will provide a form structure capable of containing concrete when placed. Most common foams are expanded polystyrene (EPS) and extruded polystyrene (XPS). ICF can be cut from blocks or custom molded. ICF can from EPS cutting machine or EPS shape molding machine. EPS Vacuum Shape Molding Machine Model: ESCX-1400 Mold Size: 1400*1200 mm Max. Product Size: 1360*1160 mm Max. Product Height: 350 mm Power: 11.5 kw Max. Contour Dimensions: 3900*2300*3800 mm Approx. Weight: 7500 kg Other available model(s): ESCX-680/790/810/812/1200/1600/1800/2000 Picture(s) & standard dimensions only for reference. Can be customized to order quick pressurized filling and interval filling large steam inlet and outlet, fast molding revolving steam conveying,

Ningbo Haiyong Plastic Machinery Co.,Ltd is the manufacturing of plastic injection molding machine in China . Our company founded in 2001 .   We have passed ISO 9001 in 2005 . Our sales is more than 6,000,000 USD in 2008 . We develop step by step . We start to develop oversea market from the end of 2008 . Our machine is from 500KN to 13000KN . We have good quality and good price . Hope to cooperate with you . Please feel free to contact me .  

After melting the ETP, it crystallizes and shapes plates (strips), bars, tubes in different shapes and specifications. Then the tractor will draw them out continuously and horizontally .

Parameters:      

Offering high performance EPS block molding machine.

Fully Automatic EPS/EPE/EPP Styrofoam Molding Machine

Offering a wide range of pet blow moulding machine.

FM-20 Foamed concrete Casting Machine Specifications (flooring, roof heat preservation and insulation) I. FM-20 Foamed concrete Casting Machine Process FM-20 mixes cement, fly ashes, and water in a ratio in the mixer into cement slurry, and then transport cement slurry to pipeline through hydraulic feed cylinder. After foaming agent dilutes by water, it will be mixed with compressed air in a certain ratio, and therefore causes high density, closed-cell foam in the pipeline. In the final step, this foam will mix with cement slurry and turn into final product, foam cement. (See complete processing diagram): II. Performance and Technical Data By adopting double cylinder hydraulic press to deliver concrete, FM-20 is able to meet the need of constructing higher buildings because of its higher pumping ability. 1. Full-automatic controlling system controls mixing ratio of variety of materials refilling process; 2. Density is easy to adjust;

Solder ball number per time:40 Solder ball spec:diameter 15mm-35mm Machine dimension:500*500*800mm Machine weight:200kg

Offering blow molding machine: Plastic molding machines adopt PLC auto controlling system which combines the electrical equipment with hydraulic pressure, matched with corresponding die and moulds, this machine can produce such plastic containers as bottles, barrels, kettles, basins, jars, boxes, and toys, etc. models for hogsheads from 0. 1ml to 50kl are all available.

YM-3P-B blow moulding machine YM-3P-B two step semi automatic compauter controlled revotary infrared oven heating bottle blowing machine is suitable for producing pp/pet plastic containers in 7l with wide mouth 28-120. It has high air pressure, big clamping force, small size, low power consumption easy to operate and maintain.

Yuexiang industry group co. ,limited(yxigc) was established in 1996 as a professional manufacturer and supplier specializing in manufacture of blow molding machines, plastic molds, and plastic products.

Including: 22MM/1-OZ OR 3OMM/2-OZ Reciprocating Screw Injection 4, 6 or 12 Station, 25" Diameter 5/8" Stainless Steel Rotary Table 25 Ton Equivalent Hydro Mechanical Clamp Water Jackets on Barrel for Barrel Cooling 4 Station Electric Mold Heating Controller Microprocessor-Based Controls Automatic Knock-Out Heat Exchanger for Oil Cooling

Vertical injection molding machine, vertical clamping from bottom vertical injection from top, clamping force from 12 ton to 210 rotary table type with 2 stations or 3 stations.

Molding Machine · The Molding Machine can be made by customer demands. It is made by stainless steel; · This machine has several kinds of blades which can produce all kinds of Demark crisp bread. · The machine has two types: Electric and Gas.

ZHF2500A series, Vacuum Press Machine is used for coating different shape base material with PVC film,wood veneer,etc by vacuum abnormality wrapping technology.It is used for coating natural wood carved board,decorative material, MDF,etc. and also can be used for heating print.It adopts the touching screen PLC control technology.It has 10 kinds of memory functions of processing model and several sub stepped absorbing functions. It also has the function like cooling the working piece when it out of the machine.

Offering blow molding machine: Plastic hollow product with volume ranges from 5ml to 230L. - Application range: Products produced by our machine can be used as packaging parts of medical, chemical, oil, food, lighting, tools, automotive, motorcycle, cosmetic, shoes, toy, etc.

Casting Machine.

SL-VP Mattress Vacuum Machine

Offering continuous casting machine: 1. Casting Pattern: 1; 2 current. 2. Casting Material: bronze, brass. 3. Casting Thickness: 350 mm; 450 mm; 650 mm. 4. Casting Width: 12 to 20 mm.

TK TECH all-round machine series: Application: Shock-absorption foam packaging material for home appliance & industrial sensitive product, Component of Automobile/Electronic goods, Fruit & fish transportation container, etc. - High quality & reliability vacuum type product manufacturing machine. - High performance and production efficiency by minimum operator. - Various product shape available. - Easy & simple shape mold change system. - Fast & short pressurized filling system. - Short cycle time & energy saving system. - Advanced Touch Screen Control system for friendly and easy operation. - Central vacuum system available (option)

use: this unit uses lldpe as main material and adopts several kinds of resins to manufacture the single/double-side self-sticky stretch wrapping film. The film has good tensile strength,anti-pricking ability and impact strength. Its good shrinking memory function and self-sticky can make goods integrity to prevent goods from loosening and collapsing during transportation and being polluted by dust. The transparency and tensile strength of this product can make the packaging beautiful, economical and practical. The film can be widely used in wrapping of palletized goods. It’s a good substitute for hot shrinking packaging film during transportation.    

This machine is available with one post or two posts, and with heat mould, cold mould and hot/cold mould, as you need, but always for one only operator. This machine mould the vamps (insteps) by heat and pressure with silicone moulds and aluminum cushions which can be changed easily, according to different upper models.

Jackson Machinery's FLEXIMATIC is an extremely versatile intermediate sized accumulator head industrial blow molding machine which features excellent uniformity of parts and extremely fast tooling changeover capability between jobs.

Respond to today?s high energy cost, friendly working environment requirements, FKI has developed and introduced All Electric Blow Moulding Machine for the packaging industry producing pharmaceutical, cosmetic and beverage bottles in sterile rooms. All Electric Blow Moulding Machine is a total new innovation design with fully electrically operated on the parison control, blow pin, the mold carriage and clamp in stead of those traditional hydraulic system with oil pump, oil cylinder and valves which significantly reduce energy consumption, gives higher production rate, less maintenance cost, noise level much reduced, in long term total production cost being dramatically reduced.

Technical specification:Die locking force (KN) 1800Size of moving platen(mm) 740X720 Diameter of tie bar (mm) 85Inner space between the bars(HV) (mm) 480X450Die thickness(min-max) (mm) 200-650Die stroke (mm) 350Ejection stroke (mm) 80Ejection force (KN) 100 Injection force (min-max) (KN) 140-220Diameter of shot shot sleeve (mm) 50, 60, 70Eceentric position of shot sleeve (mm) 0-140Dosage of fluid metal per shot(AL) (kg) 2.0Projecting area of casting(min-max) (cm2) 113-368Injecting pressure(min-max) (Mpa) 49-15Injecting stroke (mm) 360Injecting speed (m/s) 10Pressure build up time (ms) <30Dry cycle (sec) 7Pipe line pressure (Mpa) 12Motor power (Kw) 15Machine weight (Kg) 5800 Overall dimensions (LXWXH) (mm)

1) Change strainer Without need to stop running of double working positions 2) Belgium VERBRUGGEN oil cooling type automatic die head ABC distributor 3) Germany HAHL casting film roller and cooling roller 4) America NDC infrared thickness gauge 5) Denmark VETAPHONE corona machine 6) Full automatic coiler of double working positions 7) Hydraulic mould unloading wagon 8) Electric shaft extractor 9) Can regulate coiling tension through closed loop multiple stage tension taper can be set

We are a diverse United States based manufacturer of spin casting machines & supplies for the metals and wood products industries. Our mission is to ensure your success by assisting you in first finding the right solution then delivering the quality spin casting machine and equipment required for your metal and woodworking applicationsand to do so while always providing the best support in the industry. Copyright 2005 Conquest Industries, Inc. All rights reserved 12740 Lakeland Rd., Santa Fe Springs, CA 90670 Phone (800) 368-2278 - Fax (562) 906-1112

MEMCO Offers its MEMBLOW series (our stretch blow molding machines), which successfully combines the proven simplicity and reliability with the most recent developments in the PET processing technology. User- friendly controls, high productivity, reduced maintenance and operating costs are part of the attractiveness of our MEMBLOW series. Process Description Preform Ioading: The preforms are conveyed from a large capacity hopper to the automatic unscrambler where they are oriented. From the unscrambler, they travel down the support rails by gravity. At the end, a robot places the preforms upside down onto the pins of the preform carriers. Preform transferring: The preform carriers are fixed on a heavy duty chain, so that the distance between them remains constant. The chain transfer achieved by a special indexing gear which guarantees high precision and repeatability.

Offering injection molding machine for making eye drop bottles.