| Screen Size |
70 inch – 1000 inch |
| Display Type |
DLP Chip × 3 (R, G, B), DLP Projection System |
| Model Number |
PT-DS12K |
| Brand |
Panasonic |
| Resolution |
1400 × 1050 pixel (Input Signals That Exceed This Resolution Will Be Converted To 1400 × 1050 pixel) |
| Power supply |
120 V AC, 9.1 A, 50/60 Hz; 220–240 V AC, 4.8 A, 50/60 Hz |
| Power consumption - 120 V AC, 50/60 Hz |
980 W (1,010 VA) (0.2 W with standby mode set to eco.1 6 W with standby mode set to normal. Both with fan stopped.) |
| Power consumption - 220–240 V AC, 50/60 Hz |
950 W (980 VA) (0.3 W with standby mode set to eco.1 9 W with standby mode set to normal. Both with fan stopped.) |
| DLP chip - Panel size |
24.1 mm (0.95 inches) diagonal (4:3 aspect ratio) |
| DLP chip - Pixels |
1,470,000 (1,400 × 1,050) × 3, total of 4,410,000 pixels |
| Lens |
Optional powered zoom/focus lenses |
| Lamp |
380 W UHM lamps (× 2) (dual lamp, high mode) |
| Brightness |
12,000 lumens (dual lamp, high mode) |
| Center-to-corner uniformity |
90% |
| Contrast |
10,000:1 (full on/full off, in dynamic iris 3 mode) |
| Scanning frequency - SDI |
Dual-link HD-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 372 compliant: 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p Dual-link HD-SDI signal (X Y Z 4:4:4 12-bit): SMPTE ST 372 compliant: 2048 × 1080/24p, 2048 × 1080/24sF, 3G-SDI signal (RGB 4:4:4 12-bit/10-bit): SMPTE ST 424 compliant: 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p 3G-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 424 compliant: 1125(1080)/60p, 1125(1080)/50p HD-SDI signal (YPBPR 4:2:2 10-bit): SMPTE ST 292 compliant: 750(720)/60p, 750(720)/50p, 1125(1035)/60i, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p SD-SDI signal (YCBCR 4:2:2 10-bit): SMPTE ST 259 compliant: 525i(480i), 625i(576i) |
| Scanning frequency - HDMI/DVI-D/RGB |
Horizontal: 15 kHz–100 kHz, vertical: 24 Hz – 120 Hz, dot clock: 25–162 MHz or lower (HDMI/DVI: 25 MHz – 162 MHz) |
| Scanning frequency - YPBPR (YCBCR) |
525i (480i): fH 15.75 kHz; fV 60 Hz, 625i (576i): fH 15.63 kHz; fV 50 Hz, 525p (480p): fH 31.50 kHz; fV 60 Hz, 625p (576p): fH 31.25 kHz; fV 50 Hz, 750 (720)/60p: fH 45.00 kHz; fV 60 Hz, 750 (720)/50p: fH 37.50 kHz; fV 50 Hz, 1125 (1035)/60i: fH 33.75 kHz; fV 60 Hz, 1125 (1080)/60i: fH 33.75 kHz; fV 60 Hz, 1125 (1080)/50i: fH 28.13 kHz; fV 50 Hz, 1125 (1080)/25p: fH 28.13 kHz; fV 25 Hz, 1125 (1080)/24p: fH 27.00 kHz; fV 24 Hz, 1125 (1080)/24sF: fH 27.00 kHz; fV 48 Hz, 1125 (1080)/30p: fH 33.75 kHz; fV 30 Hz, 1125 (1080)/60p: fH 67.50 kHz; fV 60 Hz, 1125 (1080)/50p: fH 56.25 kHz; fV 50 Hz |
| Scanning frequency - Video/S-Video |
fH: 15.75 kHz, fV: 60 Hz [NTSC/NTSC4.43/PAL-M/PAL60] fH: 15.63 kHz, fV: 50 Hz [PAL/PAL-N/SECAM] |
| Optical axis shift - Vertical |
±50% (±40% with the ET-D75LE6) from center of screen, powered |
| Optical axis shift - Horizontal |
±30% (±20% with the ET-D75LE6) from center of screen, powered |
| Keystone correction range |
Vertical ±40°, horizontal ±15° (vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6) When using only the KEYSTONE correction of the Geometric Adjustment function: Vertical ±40°, horizontal ±15° When using the optional upgrade kit ET-UK20: Vertical ±40° and horizontal ±40° with the ET-D75LE1/LE2/LE10/LE20, vertical ±45°and horizontal ±40° with the ET-D75LE3/LE4/LE30/LE40, vertical ±22° and horizontal ±15° with the ET-D75LE5/LE50, vertical ±28° and horizontal ±15° with the ET-D75LE6. When using both the KEYSTONE and CURVED corrections of the Geometric Adjustment function: Vertical ±20°, horizontal ±15° (vertical ±8° and horizontal ±8° with the ET-D75LE5/50, vertical ±10° and horizontal ±10° with the ET-D75LE6) |
| Installation Terminals |
Ceiling/floor, front/rear |
| Installation Terminals - SDI IN 1 |
BNC × 1, Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-A) 3G-SDI signal: SMPTE ST 424 compliant HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant |
| Installation Terminals - SDI IN 2 |
BNC × 1, Dual-link HD-SDI signal: SMPTE ST 372 compliant (Link-B) HD-SDI signal: SMPTE ST 292 compliant SD-SDI signal: SMPTE ST 259 compliant |
| Installation Terminals - HDMI IN |
HDMI 19-pin × 1, Deep Color, compatible with HDCP, 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p, VGA (640 × 480) – WUXGA (1,920 × 1,200), dot clock: 25 MHz –162 MHz |
| Installation Terminals - DVI-D IN |
DVI-D 24-pin × 1, DVI 1.0 compliant, HDCP compatible, for single link only 525i(480i), 625i(576i), 525p(480p), 625p(576p), 750(720)/60p, 750(720)50p, 1125(1080)/60i, 1125(1080)/50i, 1125(1080)/25p, 1125(1080)/24p, 1125(1080)/24sF, 1125(1080)/30p, 1125(1080)/60p, 1125(1080)/50p VGA (640 × 480) – WUXGA (1,920 × 1,200), dot clock: 25 MHz –162 MHz |
| Installation Terminals - RGB 1 IN |
BNC × 5 |
| Installation Terminals - RGB 1 IN - R, G, B |
R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
| Installation Terminals - Y, PB, PR (Y, CB, CR) |
Y: 1.0 Vp-p (including sync signal), PB/PR (CB/CR): 0.7 Vp-p, 75 ohms |
| Installation Terminals - S-Video signal |
Y: 1.0 Vp-p, C: 0.286 Vp-p, 75 ohms |
| Installation Terminals - RGB 2 IN |
D-sub HD 15-pin (female) × 1 |
| Installation Terminals - R, G, B |
R: 0.7 Vp-p, 75 ohms, G: 0.7 Vp-p (G: 1.0 Vp-p for sync on G), 75 ohms, B: 0.7 Vp-p, 75 ohms HD, VD/SYNC: TTL, high impedance, positive/negative automatic |
| Installation Terminals - VIDEO IN |
BNC × 1, 1.0 Vp-p, 75 ohms |
| Installation Terminals - 3D SYNC 1 IN/OUT |
BNC × 1, 1.0 Vp-p, 75 ohms Input: TTL, high impedance. Output: TTL, max. 10 mA |
| Installation Terminals - 3D SYNC 2 OUT |
BNC × 1, 1.0 Vp-p, 75 ohms, TTL, max. 10 mA |
| Installation Terminals - SERIAL IN |
D-sub 9-pin (female) × 1 for external control (RS-232C compliant) |
| Installation Terminals - SERIAL OUT |
D-sub 9-pin (male) × 1 for link control (RS-232C compliant) |
| Installation Terminals - REMOTE 1 IN |
M3 jack × 1 for wired remote control |
| Installation Terminals - REMOTE 1 OUT |
M3 jack × 1 for link control |
| Installation Terminals - REMOTE 2 IN |
D-sub 9-pin × 1 for external control (parallel) |
| Installation Terminals - LAN |
RJ-45 × 1 for network connection, 100Base-TX/10Base-T, compliant with PJLink (class 1) |
| Power cord length |
3.0 m (9 10 in) |
| Cabinet materials |
Molded plastic |
| Dimensions (W × H × D) |
530 × 200 × 548.5 mm (20-7/8 × 7-7/8 × 21-19/32 inches) (without lens) |
| Weight |
24 kg (52.9 lbs) (without lens) |
| Operation noise |
45 dB (high mode), 43 dB (middle mode), 37 dB (eco mode) |
| Operating temperature |
0°– 45°C (32°–113°F) |
| Operating humidity |
10%–80% (no condensation) |
| Remote control unit - Power supply |
3 V DC (AA/R6 type battery × 2) |
| Remote control unit - Operation range |
Approx. 30 m (98 5 in) when operated from directly in front of the signal receptor |
| Remote control unit - Dimensions (W × H × D) |
51 × 176 × 28 mm (2 × 6-15/16 × 1-3/32 inches) |
| Remote control unit - Weight |
Approx. 134 g (4.7 oz) (including batteries) |
| Supplied accessories |
Power cord (×1) (x2 for PT-DS12KE) Wireless/wired remote control unit (× 1) Batteries for remote control (AA/R6 type × 2) Softwar Lens drop-prevention screw (× 1) e CD-ROM (Logo Transfer Software, Multi Projector Monitoring & Control Software) (× 1) |
| Optional accessories |
Zoom lens (1.0 –1.2:1) - ET-D75LE6, Zoom lens (1.4 –1.8:1) - ET-D75LE10, Zoom lens (1.8 – 2.6:1) - ET-D75LE20, Zoom lens (2.6 – 5.1:1) - ET-D75LE30, Zoom lens (5.0 – 8.0:1) ET-D75LE40, Zoom lens (7.9 –15.0:1) - ET-D75LE8, Fixed-focus lens (0.8:1) - ET-D75LE50, Lens motor cover - ET-D75MC1, Ceiling mount bracket - ET-PKD120H (for high ceilings) ET-PKD120S (for low ceilings), Attachment for ceiling mount bracket - ET-PAD310, Frame - PFD310, Smoke cut filter - SFD320, Replacement smoke cut filter - ET-SFR320, Upgrade kit - ET-UK20, Replacement lamp unit - ET-LAD310A (one bulb) ET-LAD310AW (a set of two bulbs), Replacement lamp unit for portrait mode - ET-LAD320P (one bulb) ET-LAD320PW (a set of two bulbs), Replacement filter unit - ET-EMF320 |